红薯打粉机 莲藕粉薯类磨碎机 全自动型红薯打粉机厂家

华升牌淀粉机属全封闭节能型，结构合理，性能优良，造型美观，具有自动进料，破碎分离，排渣，省时省工，更换筛网的时间可在半个小时内完成，提高了淀粉的提粉率，淀粉提取率在 98 以上，此辊带水生产，使淀粉纯白度更高，该机每小时生产量，配用千瓦电动机，可操作性强，可直接安装四轮拖拉机前工作、手扶拖拉机、电动机配套使用，该机安装使用维护、移动方便，是个体户的理想设备。

华升牌淀粉分离机一次完成鲜薯的粗破碎、细磨浆、浆渣分离，广泛应用于各中、小规模淀粉厂及家庭用户的运用。

华升牌淀粉机结构简单，使用方便，运转平稳，生产率高，维修便利。能够一次完成鲜薯的粗破碎、细磨浆、浆渣分离三道工序，能够重复利用浆液，减少了淀粉生产过程中的废水。

红薯淀粉分离机改变了手工生产淀粉时因氧化造成的淀粉光彩变差、变暗的现象;加工过程中被破碎打垮的粉渣在显微镜下呈丝状，有利于淀粉从纤维上游离出来，因此进一步提高了淀粉的提取率。

Sweet potato flour beater lotus root flour potato grinder automatic sweet potato flour beater manufacturer

Huasheng brａnd starch machine is a fully enclosed energy-saving type, with reasonable structure, excellent performance, beautiful shape, with automatic feeding, crushing and separation, slag discharge, saving time and labor. The screen screen can be changed in half an hour. The starch extraction rate is 98 The production capacity of the machine is Dun per hour, equipped with KW electric motor. It can be directly installed in front of the four-wheel tractor, walking tractor and motor supporting use. The machine is easy to install, use, maintain and move. It is an ideal equipment for individual households.

Huasheng starch separator is widely used in small and medium-sized starch factories and household users.

Huasheng starch machine has the advantages of simple structure, convenient use, stable operation, high productivity and convenient maintenance. It can complete three processes of fresh potato coarse crushing, fine refining and pulp residue separation at one time. It can reuse the slurry and reduce the waste water in the starch production process.

Sweet potato starch separator changes the phenomenon that starch luster becomes poor and darkens due to oxidation when starch is produced by hand; the broken powder residue in the processing process is filiform under the microscope, which is conducive to the starch dissociation from the fiber, so the extraction rate of starch is further improved.

薯类制粉设备主要由螺旋清洗机、刨碎分离机、磨浆分离机、渣浆分离组合筛和搅拌机等单机组合而成，特别适合于乡镇企业和户用于马铃薯和甘薯等薯类淀粉的加工。

操作人员在娴熟地掌握设备的性能、机械结构和操作规程后才能上岗作业。操作时，若设备发生故障，应对症采取以下维修和保养措施：

1、分离机常见故障及排除使用时，磨浆分离机磨片间隙应调整为毫米左右，操作时先拧上部的手柄以使螺旋旋紧，然后回退90度即可；如果刨碎分离和磨浆分离机在工作时出现主轴卡碰，应立即停车检查；若发现轴承损坏应及时更换同型号的轴承；制粉机组工作时，若发现刨碎分离机的电流表长时间处于超载状态，应调整清洗机的喂人量。

特别注意的是：刨碎分离机和磨浆分离机一定要严防铁石等硬杂物进入机内，以免损坏机件。

2、整机维修及保养要点：小型薯类制粉设备各传动轴承应经常加注润滑油、脂，尤其是磨浆分离机和刨碎分离机主轴两端的油杯，每工作48小时应加注一次钙基润滑脂，整机每月须定期保养一次；

制粉组合单机上所有的电器设备和传动皮带均不得打湿或进水，以免发生短路或皮带打滑事故；若发现传动皮带打滑应及时调整皮带轮距，使皮带涨紧；清洗机螺旋下的钢丝网使用一定的期限后易损坏，每加工50万公斤鲜薯后应予以更新；刨丝滚筒上装置的齿条使用一段时间后，若发现生产效率下降、粉渣变粗，应将齿条拆下，换另一面新齿继续使用；薯类制粉机组停用后，应对整机维修保养，清洗轴承并注足滑润油、脂，所有电器设备均应采取防潮措施，以免影响设备的性能和使用寿命。

Potato milling equipment is mainly composed of screw cleaning machine, planer separator, grinding separator, slag slurry separation combined screen and blender. It is especially suitable for processing potato and sweet potato starch in township enterprises and households.

The operator can work only after mastering the performance, mechanical structure and operation rules of the equipment. In case of equipment failure during operation, the following repair and maintenance measures shall be taken:

1. When using the separator, the disc clearance should be adjusted to about mm. During operation, the upper handle should be screwed tightly, and then it can be backed back 90 degrees. If the main shaft of the crushing separation and pulp separator collides, the machine should be stopped for inspection immediately. If the bearing is damaged, the bearing of the same type should be replaced in time; the pulverizing unit works If it is found that the ammeter of the crushing separator is overloaded for a long time, the feeding amount of the cleaning machine should be adjusted.

Special attention is: Planer separator and grinding separator must strictly prevent iron and stone and other hard debris into the machine, so as to avoid damage to machine parts.

2. Main points for maintenance and repair of the whole machine: lubricating oil and grease should be added to the drive bearings of small potato milling equipment, especially the oil cups at both ends of the main shaft of the grinding separator and the planer separator. Calcium based grease should be added once every 48 hours of operation, and the whole machine should be maintained regularly once a month;

All electrical equipment and driving belts on the single machine of pulverizing unit shall not be wet or watered, so as to avoid short circuit or belt slipping accident; if the transmission belt is found to be slipping, the belt wheel gauge shall be adjusted in time to make the belt tight; the wire mesh under the screw of the cleaning machine is easy to be damaged after a certain period of time, and it shall be renewed after processing 500000 kg of fresh potatoes; the rack of the device on the shaving drum is used to make the belt tight After using for a period of time, if it is found that the production efficiency decreases and the powder slag becomes coarse, the rack should be removed and replaced with a new tooth on the other side for continuous use; after the potato flour milling unit is out of service, the whole machine should be repaired and maintained, and the bearing should be cleaned and filled with lubricating oil and grease. All electrical equipment should be provided with moisture-proof measures to avoid affecting the performance and service life of the equipment.

欢迎电话咨询或到厂考察试机，联系电话